Roofing referrals for Seattle & nearby townsCall: (206) 984-7830
(206) 984-7830

Chimney Flashing Repair in Seattle, WA

roofingseattle.net

Get matched with an independent roofer who fixes the metal seams around a Seattle chimney.

Stains near the fireplace wall?
Call now to be connected with a local roofing contractor in Seattle.
(206) 984-7830

Chimney flashing is the metal that seals the joint between a chimney and the roof, and it is one of the most common places for a Seattle roof to leak during the wet season. Repair can mean resealing, replacing a few pieces or rebuilding the whole set. Call the number on this page to be connected with a local roofing contractor in Seattle.

A brick chimney with new metal flashing installed on a shingled roof, chimney flashing repair in Seattle, WA

What chimney flashing does

Where a masonry or framed chimney passes through a roof, water has to be steered around it. Roofers do that with layered metal: step flashing along the sides, a back piece called a cricket or saddle on the uphill side, and an apron across the downhill face. Counterflashing tucked into the brick or siding covers the top edge. Each piece overlaps the next so water runs over seams instead of into them.

Signs the flashing needs attention

  • Brown stains on the ceiling or wall beside the fireplace
  • Drips in the attic along the chimney framing after steady rain
  • Visible gaps, rust or lifted metal seen from the ground or with binoculars
  • Crumbling mortar or old sealant where the brick meets the roof

Seattle's rainy season runs from October through March, and more than 75 percent of the year's precipitation falls in that stretch, so a small gap can go unnoticed all summer and then show up in the first heavy fall storm. Older craftsman homes often have brick chimneys that have shifted slightly over the decades, which opens seams.

What a repair looks like

The roofer typically inspects the chimney area, removes nearby shingles, and checks the underlayment and decking for rot before replacing or rebuilding the flashing. Sealant alone is sometimes used as a patch, but it dries out, and many roofers prefer replacing metal. If the chimney is wide, a cricket on the uphill side keeps water and needles from pooling behind it. Moss and debris from nearby firs can collect in that same spot, so ask how the roofer plans to handle it.

Call now to be connected with a local roofing contractor in Seattle.
(206) 984-7830

What it can cost

Angi's national figures put chimney flashing repair or replacement at roughly $400 to $1,600 per job, with step flashing alone around $400 to $600. These are national numbers, not a Seattle quote. Access, chimney size, roof pitch and hidden water damage move the price, and tall or steep roofs usually cost more.

Safety and hiring

Do not climb onto a wet or mossy roof to look at a chimney. Check from the ground or with binoculars, look at the attic with a flashlight, and set a bucket under any drip. Washington requires roofers to register with L&I, so look up the company on L&I's Verify a Contractor tool before signing. Ask for a written bid that names the flashing material, whether shingles around the chimney will be replaced, and who handles cleanup.

If the same job is part of a bigger leak, see roof leak repair, or ask about roof flashing repair for vents and walls elsewhere on the roof.

Chimney Flashing Repair questions from Seattle homeowners

Can chimney flashing be fixed with caulk?
Sealant can slow a small leak for a while, but it cracks as the roof heats, cools and gets soaked. Many roofers replace damaged metal instead and use sealant only as a secondary detail. Ask which approach your bid assumes.
Is a chimney leak always the flashing?
No. Cracked masonry, a failed chimney cap, or condensation inside the flue can also show up as ceiling stains. A roofer or chimney specialist can tell which one you have.
Why does my chimney only leak in heavy Seattle rain?
Small gaps often let water in only when rain is wind-driven or steady for days. The wet season from October to March tends to expose them.
Do I need a permit for chimney flashing work?
Seattle's SDCI requires a re-roof permit when repairing an area over 500 square feet, so a small flashing repair generally falls below that. Ask the roofer who confirms permit needs for your address.

Related roofing services in Seattle

Chimney Flashing Repair in nearby cities and towns

King County

Snohomish County

Pierce County

Kitsap County

Island County

Mason County

Jefferson County

Call now to be connected with a local roofing contractor in Seattle.
(206) 984-7830

Last updated:

☎ Call (206) 984-7830